The Art of Basic Plumbing for Installing a Bathtub
The Art of Basic Plumbing for Installing a Bathtub
Blog Article
Nearly everybody is bound to have his or her own theory about Tools You Need to Install a New Bathtub .
Installing a bath tub isn't specifically brain surgery, however it does call for strong plumbing, woodworking, and in some cases, tiling skills. Changing an old tub with a new one is additionally a moderately tough project. If the old bathtub is readily easily accessible, the project can move easily; if you have to open a wall surface to get rid of the old bathtub and position the brand-new tub, the task is much harder. In either case, the task is within a home handyman's abilities, although you will certainly require an assistant to leave the old tub and also embeded in the brand-new one. Make sure you have actually certified on your own for the work and also are comfortable trying it. As opposed to employing a professional to take over a halfway-completed job, it is much better to take into consideration employing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will help you set up a new bathtub in your restroom if you have actually already purchased a new bathtub and also don't need to transform the setup of your previous water pipelines.
Your tools and also product checklist need to make up the following:
Getting ready for the Installation
Firstly, the supporting framework supplied with the bath needs to be fitted (if required) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to see to it that if the tap features a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you use every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to now prepare to be suited its last position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the water system. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be rather troublesome as a result of the limited accessibility that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the remaining water that will come from the pipelines. As soon as the supply pipelines have actually been gotten rid of, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single taps from transforming throughout this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any old securing compound.
Prior to carrying on to fit the brand-new taps, contrast the pipe links on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Making use of both wood boards under its feet, position the bath tub in the required setting. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four tiny factors.
The following objective is to make certain that the tub is leveled all round. This can be attained by inspecting the level as well as changing the feet on the tub till the level reviews level.
To set up taps, fit the bottom of the furthest versatile tap connector to the ideal supply pipeline by making a compression sign up with; after that do the very same for the other faucet.
Switch on the water supply and also check all joints and new pipework for leaks and also tighten them if needed. Load the tub as well as likewise inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
Ultimately, fix the bathroom paneling as defined in the producer's instruction manual. Tiling as well as sealing around the bath tub should wait until the tub has been used at the very least when as this will resolve it into its last position.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will call for lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin ensuring that the washers are in place in between the tap and the sink. Protect the tap in place with the maker offered backnut. As soon as the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former type should be attached to the tap finishes initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath meets the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to crack a stiff seal, triggering the water to pass through the wall surface in between the bathroom and the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes and cartridges, and can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to allow for the activity experienced when the tub is in usage. The sealer can fracture rather very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise quickly readily available on the market. It is a good idea to fit the floor tiles making use of waterproof or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a devoted person who reads about Installing A Bathtub, I figured sharing that article was mandatory. Sharing is caring. Helping people is fun. I take joy in reading our article about Installing A Bathtub.
Check This Out Report this page